Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| minutes [2009/01/08 17:50] – mstudli | minutes [2009/01/15 01:41] (current) – removed jonmash | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ==== Meeting Minutes - January 7th, 2009 ==== | ||
| - | |||
| - | |||
| - | **Present: | ||
| - | * Jonathan Mash | ||
| - | * Mike Studli | ||
| - | * Liliane Barbour | ||
| - | |||
| - | **Agenda** | ||
| - | * Blueprint paper - task assignment | ||
| - | |||
| - | |||
| - | **Discussion: | ||
| - | * Liliane is in charge of contacting Dr. Hashtrudi-Zaad to set-up a meeting time | ||
| - | * All team members are to finalize their course schedule in order to plan arranged meeting times | ||
| - | * Task assignments were arranged to optimize the blueprint writting procedure | ||
| - | * Control board and motor control board interfacing standard was discussed and agreed upon | ||
| - | |||
| - | |||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | |||
| - | |||
| - | |||
| - | ==== Meeting Minutes - Nov 14, 2008 ==== | ||
| - | |||
| - | Sensors | ||
| - | * Putting blinders on sensors | ||
| - | * Problem that it might not detect close objects. | ||
| - | * Need more cure for sensors to each have their own area. | ||
| - | * Need to test thermal sensor -> see if can be used to differentiate between objects | ||
| - | * Will order more PIRs later in case some get damaged | ||
| - | |||
| - | Motor | ||
| - | * How much force on gears? Don’t want to break | ||
| - | * If use gears can use a smaller stepper motor | ||
| - | * Algorithm: | ||
| - | * Spline curve -> so can start acceleration with zero slope at beginning and zero slope at end | ||
| - | * Spline toolbox in MATLAB | ||
| - | |||
| - | Electrical | ||
| - | * Heat sinks | ||
| - | * Do we need an enclosure? | ||
| - | * Test on bigger TVs | ||
| - | |||
| - | Microcontroller | ||
| - | * Need a lot of analog ports -> 8? | ||
| - | * Serial output | ||
| - | |||
| - | Ordering plan | ||
| - | * Buy pre-fab controller, and purchase PING, etc. | ||
| - | * When see how much money left, then buy parts for custom controller and PIR sensors | ||
| - | * PERF board | ||
| - | * Need to put PCB boards in the budget | ||
| - | |||
| - | What we need now | ||
| - | * Excel table with minimum costs in a budget | ||
| - | * Possible other budget with custom controller, etc. | ||
| - | |||
| - | For next week | ||
| - | * Budget | ||
| - | * Test thermal sensors | ||
| - | *Test volume | ||
| - | * Look for evaluation board for controller | ||
| - | * Ease of programming | ||
| - | * Power supply | ||
| - | * memory | ||
| - | |||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | |||
| - | |||
| - | ==== Meeting Minutes - Nov 20, 2008 ==== | ||
| - | |||
| - | |||
| - | |||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | --------------------------------------------------------------------------------------------------- | ||
| - | |||
| - | |||
| - | |||
| - | ==== Meeting Minutes - October 30th, 2008 ==== | ||
| - | |||
| - | **Present: | ||
| - | * Dr. Hastrudi-Zaad | ||
| - | * Jonathan Mash | ||
| - | * Mike Studli | ||
| - | * Liliane Barbour | ||
| - | |||
| - | **Agenda** | ||
| - | * Proposal paper | ||
| - | |||
| - | |||
| - | **Discussion: | ||
| - | |||
| - | * Reviewed proposal report | ||
| - | |||
| - | * Looked at web-site | ||
| - | |||
| - | * Clean front end of web-site | ||
| - | |||
| - | * Have some password protection option | ||
| - | |||
| - | **Project: | ||
| - | |||
| - | * Check devices but we may need budget approval first | ||
| - | * Contact: Steve Humphrey | ||
| - | * Items and testing devices | ||
| - | * Use volt meter and oscilloscope to test | ||
| - | * Particular bench set-up if we need special equipment | ||
| - | * Research proximity sensors | ||
| - | * Discussed next meeting date | ||
| - | * * field trip next Thursday so the following Thursday November 13th | ||
| - | |||
| - | |||
| - | **Deliverables for the next meeting** | ||
| - | |||
| - | * Deliverables for November 13th Meeting: | ||
| - | * Look at sensors | ||
| - | * Crude plan of what we want to do | ||
| - | * Present all options (uC, fpga, etc) | ||
| - | * Up-dated budget | ||
| - | * Be ready to start ordering | ||
Brought to you by: Liliane Barbour, Jonathan Mash and Mike Studli
<html><br></html>With the support of: Dr. Hashtrudi-Zaad
<html><br></html>
<html><br></html>
<html>
<script type=“text/javascript”><!– google_ad_client = “pub-9209348786221882”; /* 728×90, created 9/18/09 */ google_ad_slot = “5734138715”; google_ad_width = 728; google_ad_height = 90; –> </script> <script type=“text/javascript” src=“http://pagead2.googlesyndication.com/pagead/show_ads.js”> </script> <script type=“text/javascript”> var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-15403368-5']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script> </html>
